This is a 12 volt LED Turn Signal Kit with 2 Amber (front) and 2 Red (rear) LED lights. The 4 LED light kit comes with a turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18” ground wire and the hardware to mount it to your steering column. The 4 LED lights are 4”x 2” rectangular with 16 (LED) Light Emitting Diodes each, polycarbonate lens & housing, and hard wired with encapsulated electronics to eliminate corrosion. The Special LED Electronic Flasher has the 3 pin connections for the LOAD, PILOT and POWER. The kit also comes with an 18” black grounding wire with ring tong connector (for grounding the turn signal switch), an ATC type in-line fuse holder, a 3 amp fuse, and 9 self tapping screws for mounting the lights and flasher.
This kit can be easily installed, it does not go into any factory wiring, and it is a completely independent system that comes with the wiring diagram and instructions. Each wire has a different color and the wiring diagram shows where each colored wire goes. I include my phone number and e-mail address with the instructions, so if you have any questions about your installation you can contact me.
I supply the major quality components and hardware to mount them; you supply the color wire and connectors you want to use. The pictures below show my Polaris Ranger and my customers have installed their kits on the Polaris Razor (RZR) and Crew, the Yamaha Rhino, the Arctic Cat Prowler, the Kawasaki Mule and Teryx, the Cub Cadet Volunteer Tracker and a Dune Buggy. This kit can be easily installed on any 12 volt Side-by-Side, UTV, Golf Cart, Club Car, Sand Car, etc.
The local dealer charges $360 to install a kit with only 2 LED lights and 2 Bulb lights. You can install my 4 LED lights, turn signal switch, special LED electronic flasher, and save hundreds of dollars. This turn signal switch has been installed on thousands of units, very nice and easy to operate. The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
2 - Amber 4" x 2" LED Lights 2 - Red 4" x 2" LED Lights 1 - Turn Signal Switch w/hardware
1 - LED Electronic Flasher 1 - In-line ATC Fuse Holder 1 - ATC Type 3 Amp Fuse
1 - 18" Black Ground Wire (switch) 9 - Self Taping Screws for mounting ..... LED Lights & Electronic Flasher
Parts you supply: The color wire and connectors you want to use.
Turn Signal Switch
This is a 6, 12 or 24 volt turn signal switch, which has a pilot light for the turn signals and 4-way emergency flashers (hazard warning). The turn signal switch has a pull on flare tab for the 4-way hazard lights, an added 18" black grounding wire with ring tong connector (for grounding the turn signal switch) and the hardware to mount it to your steering column. This turn signal switch can be easily installed and comes with the wiring diagram and instructions. Each wire has a different color and the wiring digram shows where each colored wire goes.
With this turn signal switch you can supply whatever lights, flasher, in-line fuse holder and fuse, color wire and connectors you want to use. The picture below shows my Polaris Ranger and my customers have installed their turn signal switch on the Polaris Razor (RZR) and Crew, the Yamaha Rhino, the Arctic Cat Prowler, the Kawasaki Mule and Teryx, and the Cub Cadet Volunteer Tracker. This switch can be easily installed on any 12 volt Side-by-Side, UTV, Golf Cart, Club Car, Sand Car, Dune Buggy, etc. This turn signal switch has been installed on thousands of units, very nice and easy to operate.
The Motor Vehicle Department and your local police departments will be impressed. Everyone who rides on the street, off road, at the dunes or in congested riding areas, should have turn signals for there added safety.
The LED lights are 4”x 2” rectangular with 16 (LED) Light Emitting Diodes each, polycarbonate lens & housing, hard wired with encapsulated electronics to eliminate corrosion and come with the screws to mount them.
